The SR760 and SR770 are single-channel, 100 kHz FFT spectrum analysers with a dynamic range of 90 dB and a real-time bandwidth of 100 kHz. The SR770 additionally includes a low-distortion, synthesized source allowing you to measure the transfer functions of electronic and mechanical systems. The speed and dynamic range of these instruments, coupled with their flexibility and many analysis modes, makes them the ideal choice for a variety of applications including acoustics, vibration, noise measurement and general electronic use.

Transfer Function (magnitude and phase)

Limit and Data Tables

Harmonic Distortion

High Dynamic Range

The SR760 and SR770 have a dynamic range of 90 dB. This means that for a full-scale input signal the instruments have no spurious responses larger than -90 dBc (1 part in 30,000). Even signals as small as -114 dBc (1 part in 500,000) may be observed by using averaging. The low front-end noise and low harmonic distortion allow you to see signals that are buried in the noise of other analyzers.

Powerful Processing

The SR760 and SR770 use a pair of high-speed, 24-bit digital signal processors (DSPs) to filter, heterodyne and transform sampled data from its 16-bit analog-to-digital converter. These DSPs can perform 25 million 24-bit multiplications and additions each second. This computing capability allows the analyzers to operate at a real-time bandwidth of 100 kHz. In other words, the SR760 and SR770 process the input signal with no dead time. Your measurements will be done in as little as a tenth of the time of other analyzers, which typically have real-time bandwidths of about 10 kHz.

Easy To Use

The SR760 and SR770 are very easy to use. The simple, menu-oriented interface logically groups related instrument functions. Context-sensitive help is available for all keys and menus, and entire instrument setups can be saved to disk and recalled with a single key stroke.

Spectrum Measurements

The spectrum, power spectral density and input time record can be displayed in a variety of convenient linear and logarithmic units including Vp, Vrms, dBVp, dBVrms or user-defined Engineering Units (EUs). The magnitude, phase and real and imaginary parts of complex signals can all be displayed. Several window functions including Hanning, Flat-Top, Uniform and Blackman-Harris can be chosen to optimize in-band amplitude accuracy or minimize out-of-band sidelobes.

Octave Measurements

The SR760 and SR770 also compute both the 15 and 30 band 1/3 octave spectra, commonly used in acoustics and noise measurement applications. A-weighting compensation is available for octave measurements. Amplitudes are computed for band -2 (630 mHz) through band 49 (80 kHz).

Triggering and Averaging

Flexible triggering and averaging modes let you see signals as low as 114 dB below full scale. RMS averaging provides an excellent estimate of the true signal and noise levels in the input signal, while vector averaging can be used with a triggered input signal to actually reduce the measured noise level. Both rms and vector averaging can be performed exponentially, where the analyzer computes a running average (weighting new data more heavily than older data), or linearly, where the analyzer computes an equally weighted average of a specified number of records. Triggering can be used to capture transient events or to preserve spectral phase information. Both internal and external triggering are available with adjustable pre-trigger and post-trigger delays.

Synthesized Source

The SR770 includes a low-distortion (-80 dB), synthesized source which can be used to make frequency response measurements. It generates single frequency sine waves, two-tone signals for intermodulation distortion (IMD) testing, pink and white noise for audio and electronic applications, and frequency chirps for transfer function analysis. This direct digital synthesis (DDS) source provides an output level from 100 µV to 1 V, and delivers up to 50 mA of current.

Frequency Response Measurements

With its low-distortion DDS source, the SR770 is capable of performing accurate frequency response measurements. The source is synchronized with the insturment's input allowing transfer functions to be measured with 0.05 dB precision. The SR770 measures the magnitude and phase response of control systems, amplifiers, and electro-mechanical systems and displays the resulting Bode plot.

Limit and Data Tables

Sometimes it is important to keep track of a few key portions of a spectrum. The SR760's and SR770's data tables allow up to 200 selected frequencies to be displayed in a tabular format which can be printed or saved to disk. Automated entry makes it easy to set up data tables for harmonic or sideband analysis. Convenient limit tables allow the entry of up to 100 separate upper or lower limit segments for pass-fail testing. On exceeding a limit, the analyzers can be configured to generate a screen message, an audio alarm or a GPIB service request.

Analysis Modes

Three built-in analysis modes simplify common measurements. Harmonic analysis computes both harmonic power and THD (Total Harmonic Distortion) relative to a specified fundamental. Sideband analysis lets you compute power in a set of sidebands relative to the carrier power. And band analysis lets you easily integrate the power in a selected frequency band. All three analysis modes provide clear, on-screen markers which make it easy to pick out frequencies of special interest such as harmonics or sidebands.

Markers

The SR760 and SR770 have a marker that is designed to be fast, responsive and flexible. The marker can be configured to read the maximum, minimum or mean of a selected width of display, or can be set to tracking mode to lock on to a moving peak. Delta-mode readouts let you easily view frequency or amplitude differences between two peaks. Automated peak-find lets you quickly move between the peaks in a spectrum. And the markers for the upper and lower displays can be linked to easily display similarities or differences in the two spectra.

Math Functions

Data taken with the SR760 and SR770 can be processed with the built-in trace calculator. Basic arithmetic functions such as addition, subtraction, multiplication, division, square roots and logarithms can be performed on traces. Traces can be combined with other on-screen traces, or with traces stored on disks. These calculator functions are quite useful for performing background subtraction or normalization of data.

Flexible Storage and Output

All traces, data tables and limit tables can be stored using the 3.5" DOS disk drive. Data can be saved in a space-saving binary format, or an easy-to-access ASCII format for off-line analysis. A variety of hardcopy options let you easily view data from the instruments. The screen can be dumped to a dot-matrix printer or a LaserJet compatible laser printer via the standard rear-panel Centronics printer interface. Complete limit and data tables, as well as a summary of the instrument settings, can be printed. Plotter output is available to any HP-GL compatible plotter with an RS-232 or GPIB interface.

Easy to Interface

All functions of the analyzers can be queried and set via the standard RS-232 and GPIB interfaces. A comprehensive set of commands allows complete control of your analyzer from a computer. Data can be quickly transferred in binary format, or more conveniently in ASCII format. The complete command list is available as a help screen in the instruments for convenient reference while programming.